Rigid liners
Rigid stainless sections join together in straight chimneys which suits wood burning appliances well.
A sweep in Roseland can reline an unlined or damaged flue with a liner sized to the appliance and insulated where the system calls for it. Call (862) 352-3142 to reach a local chimney sweep.
Inside most chimneys is a liner, the tube that actually carries smoke and flue gases to the top. It keeps heat from reaching wood framing next to the chimney, protects the brick and mortar from corrosive gases and gives the appliance a flue of the right size to draft well. Many older homes, especially those built before the middle of the last century, have no liner at all.
There are a few reasons a chimney gets a new liner. Clay tiles crack after chimney fires, shift as the house settles and lose mortar at the joints, while some chimneys never had tiles to begin with. A new fireplace insert, wood stove or furnace also usually calls for a liner sized to that appliance, since an oversized flue drafts poorly and builds up creosote or condensation.
A camera scan of the flue shows the sweep the condition of the old liner and any offsets or obstructions. That reveals whether the existing tiles can be repaired or need to be replaced, and it shows the route a new liner will take. Ask to see the camera video so you understand what was found.
If the problem goes deeper than it first looked, a Roseland chimney sweep may also recommend chimney liner repair or chimney inspection.
Need chimney liner installation in Roseland? Call (862) 352-3142 and describe the problem to a chimney sweep who works in Roseland.
Call nowHere is how a sweep usually handles a liner installation.
The inside of the chimney is checked so the route and condition are known. The findings shape the rest of the job.
Sizing follows the appliance it will serve, since too big or too small both cause problems. The full height of the flue is measured too.
Before the liner goes in, the chimney is swept and cleared. Some chimneys need old tiles broken out to fit an insulated liner.
The stainless liner is lowered from the roof down to the appliance, often wrapped in an insulation blanket. Insulation keeps the flue warm for better draft and helps meet clearance rules.
The bottom connects to the stove, insert or appliance, and the top is sealed with a top plate and cap. Every joint is secured so gases stay inside the liner.
The appliance is fired or the draft is tested to confirm smoke and gases go up and out. This is also a good time to test your CO alarms.
Rigid stainless sections join together in straight chimneys which suits wood burning appliances well.
A cement based mix is poured around a form inside the chimney to create a smooth new flue and can add strength to older masonry.
An insulation wrap or poured insulation surrounds the liner which improves draft and limits creosote.
Flexible stainless steel liners bend around offsets in the chimney and are common for inserts, stoves and gas appliances.
Liners sized for gas and oil appliances stop condensation from damaging the chimney.
Stainless steel is the most common material for relining today, because it is strong, resists corrosion and works with wood, gas and oil. It comes in flexible coils for chimneys with bends and rigid sections for straight flues. The grade of stainless and the wall thickness are matched to the fuel, and systems are tested and listed as complete kits with their parts.
Insulation around the liner helps flue gases rise and keeps the outside of the chimney cooler. At the top, a sealing plate and cap keep rain and animals out. Many Roseland chimneys get a stainless liner when an old fireplace is converted to an insert.
A chimney is relined when the existing flue cannot safely vent the appliance. It is often recommended after a chimney fire, when clay tiles crack, or when a new appliance needs a different flue size. In most cases the work is done from the top without tearing into the house.
Before relining, it helps to know which appliances share the chimney. If the furnace was upgraded recently, the water heater may now be venting into a flue that is too large. Relining with the right size solves the draft and moisture problems.
Many chimneys in Roseland were built long before modern liners were standard. From Roseland out to places nearby like Caldwell, Pine Brook, North Caldwell and Troy Hills, wood stoves and inserts are common, and each one needs a properly sized liner, and a new liner is often the safest long term fix.
For chimney liner installation in Roseland, NJ or nearby towns like Caldwell, Pine Brook, North Caldwell and Troy Hills, call (862) 352-3142 to reach a chimney sweep who covers your street.
Winters here are long and cold, and the heating season usually runs from October well into April. Masonry takes the worst of it from the freeze and thaw cycle: water soaks into brick, mortar joints and the crown on a mild day, freezes overnight and expands, which is how cracks, loose bricks and leaks start. Wind driven rain from coastal storms finds any gap in flashing, too. That is why chimney cleaning in Roseland is usually booked in the fall, before the first cold night.
Small chimney problems caught early usually stay small repairs.
Chimney sweeps in Roseland know the chimneys and fireplaces common in local homes.
Ask your questions before you agree to anything.
More questions? Call (862) 352-3142
Fixing gaps, cracks and missing mortar inside the flue liner after a camera scan shows where the damage is.
Learn moreA top to bottom check of the chimney, inside and outside before a sale, after a chimney fire or ahead of the heating season.
Learn moreInstalling wood, gas and pellet inserts in existing fireplaces, with the chimney inspected before anything goes in.
Learn moreWood stove installation into an existing chimney or a new insulated chimney, so the stove drafts well and stays clear of anything that can burn.
Learn moreLooking for something else?
See all chimney servicesCall (862) 352-3142 to talk to a chimney sweep serving Roseland, NJ.
Free to call. No forms to fill out.